Precision PCB Fabrication, High-Frequency PCB, High-Speed PCB, Standard PCB, Multilayer PCB and PCB Assembly.
The most reliable PCB & PCBA custom service factory.
PCB News

PCB News - What preparations need to be made before drilling the circuit board factory

PCB News

PCB News - What preparations need to be made before drilling the circuit board factory

What preparations need to be made before drilling the circuit board factory

2021-08-23
View:460
Author:Aure

What preparations need to be made before drilling the circuit board factory

The circuit board factory needs to make the following preparations before drilling. It is no longer a problem to make high-quality PCB circuit boards!

1. The circuit board factory regularly cleans magnetic heads and other components:

For paper tape drives, tape drives or floppy disk devices, the heads must be cleaned up on time. In addition, the light bulbs, lenses, light-emitting tubes and photoelectric tubes of the paper tape machine must also be cleaned regularly.

2. The circuit board factory (PCB circuit board) reasonably sets the parameters:

The main parameters of the equipment include coordinates, metric system/imperial system, absolute/incremental, EIA code/ASC2 code, leading zero/post zero, etc.

The basic parameters of the drill include T (1/2/3), drill diameter, feed, speed, etc.


What preparations need to be made before drilling the circuit board factory

3. The circuit board factory preheats the equipment in advance:

The main shaft of the ball bearing must be warmed up in advance every time the ball bearing is started. If it is more than 1 hour away from use, it must be reheated. The oil mist lubricated spindle is a special case and does not require preheating. The above preheating operation can keep the CNC drilling machine safe and stable. Insufficient preheating will produce more low-quality boreholes.

So how to preheat the spindle? In fact, the drill bit is inserted into the spring chuck, the drill bit rate is controlled at 15 thousand per minute, and it must continue to rotate for a quarter of an hour. If there is a special preheating program then the efficiency will be very high. Remember that if the spring chuck rotates at a high speed without a drill bit, it will inevitably destroy the spindle. Everyone must pay attention to this!

4. The drilling quality of the circuit board factory is closely related to the radial runout of the drill shaft, so it must be tested on time. The method is still very simple: put the standard rod into the collet chuck, the dial gauge measuring head is placed about 19 mm away from the lower end of the collet chuck, and then slowly rotate the drill shaft, at this time the dial gauge moves the radial direction The amount of runout has been measured. Each drill shaft of some CNC drilling machines is equipped with a laser measuring instrument, which can measure the diameter, radial runout and axial size of the drill bit. If there is this kind of equipment, the efficiency will be improved a lot. Under normal circumstances, the replacement cycle of the spring chuck is half a year, which should be paid attention to.

5. The drill bit of the circuit board factory should be controlled at about 1.3 mm lower than the presser foot pad of the drill shaft. The sequence of drilling steps is as follows:

1. The presser foot pad first presses the laminated board of the base plate;

2. Drill down the drill bit;

3. Remove the drill bit when retracting;

4. The presser foot pad leaves the base plate stack.

The presser foot pressure of the cylinder and spring should be controlled at 21-42N/㎡. When the diameter of the drill bit is less than half a millimeter, it is better to use a rigid presser foot pad.

6. Drilling depth measured by circuit board factory

Generally speaking, all drilling thresholds are that the tip of the drill bit is exactly on the surface of the table. Everyone is familiar with the standard drill bit installation size is 0.8 inches, but there are other specifications. We generally adjust the drilling threshold to exactly 1 mm deep into the backing plate or one-half of the thickness of the backing plate. There are two reasons:

If it is too shallow, it is easy to make it difficult to drill through the substrate on the backing surface.

If it is too deep, the wear rate of the drill bit will be higher.

As a professional circuit board factory, the company focuses on the production of high-precision double-sided/multilayer circuit boards, high-end HDI boards, thick copper circuit boards, blind buried vias, high-frequency circuit boards, and PCB proofing and batch boards.