Precision PCB Fabrication, High-Frequency PCB, High-Speed PCB, Standard PCB, Multilayer PCB and PCB Assembly.
The most reliable PCB & PCBA custom service factory.
PCB News

PCB News - There are three reasons for the welding defects of the circuit board

PCB News

PCB News - There are three reasons for the welding defects of the circuit board

There are three reasons for the welding defects of the circuit board

2021-09-14
View:397
Author:Aure

There are three reasons for the welding defects of the circuit board:


1. The solderability of the circuit board hole affects the welding quality

Poor solderability of the circuit board holes will result in false soldering defects, which will affect the parameters of the components in the circuit, resulting in unstable conduction of the multi-layer board components and inner wires, causing the entire circuit to fail.

The so-called solderability is the property that the metal surface is wetted by molten solder, that is, a relatively uniform continuous smooth adhesion film is formed on the metal surface where the solder is located.


The main factors that affect the solderability of printed circuit boards are:


(1) The composition of the solder and the nature of the solder. Solder is an important part of the welding chemical treatment process. It is composed of chemical materials containing flux. Commonly used low melting point eutectic metals are Sn-Pb or Sn-Pb-Ag. The impurity content must be controlled by a certain proportion, In order to prevent the oxides generated by impurities from being dissolved by the flux. The function of the flux is to help the solder wetting the surface of the circuit to be soldered by transferring heat and removing rust. White rosin and isopropanol solvents are generally used.

(2) The welding temperature and the cleanliness of the metal plate surface will also affect the weldability. If the temperature is too high, the solder diffusion speed will increase, and it will have high activity at this time, which will cause the circuit board and the solder to melt.



There are three reasons for the welding defects of the circuit board:


The surface oxidizes rapidly, causing soldering defects. Contamination on the surface of the circuit board will also affect the solderability and produce defects. These defects include tin beads, tin balls, open circuits, and poor gloss.

2. Welding defects caused by warpage Circuit boards and components warp during the welding process, resulting in defects such as virtual welding and short circuit due to stress deformation. Warpage is often caused by the temperature imbalance of the upper and lower parts of the circuit board.

For large PCBs, warping will also occur due to the drop of the board's own weight. The ordinary PBGA device is about 0.5mm away from the printed circuit board.
When the normal shape is restored, the solder joints will be under stress for a long time. If the device is lifted by 0.1mm, it is enough to cause a virtual solder open circuit.

3. The design of the circuit board affects the welding quality

In the layout, when the circuit board size is too large, although the soldering is easier to control, the printed lines are long, the impedance increases, the anti-noise ability is reduced, and the cost increases; Mutual interference, such as electromagnetic interference of circuit boards. Therefore, the PCB board design must be optimized:

(1) Shorten the connection between high-frequency components and reduce EMI interference.

(2) Components with heavy weight (such as more than 20g) should be fixed with brackets and then welded.

(3) The heat dissipation problem should be considered for heating elements to prevent defects and rework caused by large ΔT on the surface of the element, and the thermal element should be far away from the heat source.


(4) The arrangement of components should be as parallel as possible, so that it is not only beautiful but also easy to weld, and it is suitable for mass production. The circuit board is best designed as a 4:3 rectangle. Don’t change the wire width to avoid

Discontinuity of wiring. When the circuit board is heated for a long time, the copper foil is easy to expand and fall off. Therefore, avoid using large-area copper foil.